Partial pressure blending

Partial pressure blending

Not every filling station sells the mix a dive needs, and helium is expensive enough that many technical divers blend their own nitrox and trimix. The usual way is partial pressure blending: the gases go into the tank one after another, and the pressure gauge tells when to stop. This guide explains how it works, what to watch out for and why a finished blend always gets analysed.

Ways to a mix

  • Continuous blending: oxygen is added to the intake air of a compressor, or a membrane takes nitrogen out of it, and the mix is analysed while it flows. It needs a compressor built for it and gives nitrox up to about 40 % oxygen.
  • A bank of premixed gas: large cylinders hold a standard mix, often EAN32, and the tank is filled from them.
  • Partial pressure blending: helium, oxygen and air go into the tank one by one. It needs little more than cylinders of oxygen and helium, a filling whip with a precise gauge and an air compressor, and it reaches any mix, trimix included. The rest of this guide is about this method.

The principle

By Dalton's law every gas in a tank contributes its share to the total pressure. A tank of 200 bar of EAN32 holds 64 bar of oxygen and 136 bar of nitrogen, no matter in which order they went in. Pure oxygen and pure helium can be added in any amount, but nitrogen only comes with air, and air always brings 21 parts of oxygen with every 79 parts of nitrogen. So the nitrogen of the mix fixes how much air goes in, and the oxygen of that air counts towards the oxygen of the mix. The order of the fill follows from it: first helium, then oxygen, and air last, up to the end pressure. The gas blending calculator explains the formulas step by step.

Three examples

EAN32 in an empty 12 l tank, 200 bar. Oxygen to 28 bar, then air to 200 bar. The 172 bar of air bring the nitrogen and most of the oxygen; only 28 bar have to come as pure oxygen.

Topping up. The same tank still holds 50 bar of EAN32 from the last dive. What is left counts: oxygen to 71 bar, then air to 200 bar. Without the remaining gas in the calculation, the mix would end up richer than planned.

Trimix 18/45 in a double 12, 220 bar, with 40 bar of trimix 21/35 left in it. Helium to 125 bar, oxygen to 139 bar, air to 220 bar. The 85 bar of helium are 2040 l: in a trimix the helium is by far the most expensive part of the fill, and the calculator shows what it costs at your filling station.

The calculator reads the gauge in whole bar, as you do. Some combinations cannot be reached by adding gas: when the remaining gas holds more helium or nitrogen than the mix may, the tank has to be drained first, and the calculator says to which pressure.

Heat

Compressing a gas heats it, and a warm tank shows a higher pressure than it will hold once it has cooled down. The pressure follows the absolute temperature: 200 bar at 40 °C become about 187 bar at 20 °C. Helium heats up even more than air when it is compressed. Fill slowly, let the tank cool before the last top-up, or fill in a water bath. Otherwise the tank holds less gas than planned, and the mix shifts because the first gas went in warm and the last one cooler.

Oxygen safety

Pure oxygen under pressure makes things burn that are harmless in air: oil, grease, dust and many plastics and seals. Opening a valve quickly compresses the gas behind it in a fraction of a second and heats it, which can be enough to ignite them. With partial pressure blending the tank and the valve see pure oxygen at high pressure, even when the finished mix is only EAN32.

  • Use only tanks, valves and whips that are cleaned for oxygen and lubricated with grease approved for it, and keep them that way: no ordinary air from an oily compressor into an oxygen-clean tank.
  • Open every valve slowly, and let the oxygen flow in slowly.
  • Many training agencies and filling stations treat every gas with more than 40 % oxygen like pure oxygen. Partial pressure blending puts pure oxygen into the tank, so the tank needs this standard whatever the final mix.

Mixing and analysing

The gases do not mix at once: helium in particular stays in layers for a while. Roll the tank or let it stand for some hours before you analyse it. Then measure the oxygen with an oxygen analyser, and the helium of a trimix with a helium analyser. If the result differs from the plan, plan the dive with the measured values: a richer mix has a shallower MOD, less helium a deeper END. Label the tank with its oxygen and helium, its MOD, the date and who blended it, and note the fill in a log.

Calculators for this guide

This guide explains the principles; it does not replace training as a gas blender. Blend only with equipment and gases you are trained and allowed to use, and check results against a second source; see the legal notice.