Decompression
Every dive loads the body with nitrogen, and on a trimix dive with helium as well. On the way up the pressure drops and the gas has to leave the tissues again. As long as the load is small, a slow ascent is enough. Beyond a certain point it is not, and the diver has to stop on the way up and wait. This guide explains when a dive becomes a decompression dive, how decompression is planned and what changes a plan.
No-stop dives and decompression dives
On a no-stop dive the diver may ascend straight to the surface at any time; a safety stop of a few minutes at 3 to 5 m is a good habit, but not a must. Past the no-stop limit the tissues hold so much gas that a direct ascent would risk decompression sickness. The diver now has a ceiling, a depth they must not rise above, and has to make decompression stops until the ceiling has reached the surface. These stops are not optional: there is no direct way up any more.
The step is smaller than it looks. A dive on air to 30 m for 20 minutes already asks for 4 minutes of stops with the gradient factors 30/85; five minutes longer at the bottom, and it is 11 minutes. Divers who plan near the no-stop limit should know where it lies for their dive, and carry enough gas for the stops in case they pass it.
Decompression sickness
When a tissue holds more gas than the falling pressure allows, bubbles form. Depending on where, they cause pain in the joints, skin rashes, unusual tiredness, numbness, paralysis or breathing problems, sometimes only hours after the dive. The first aid is pure oxygen and a call to the emergency services or a diving emergency hotline; the treatment is a recompression chamber. Hard work, cold, a fast ascent, little fluid and several dives a day raise the risk. No plan rules it out: decompression sickness also happens on dives that kept every limit.
How decompression is calculated
In 1908 John Scott Haldane described the body as tissues that take up and release gas with different half-times, and showed that an ascent in stages is safer than a direct one. Albert Bühlmann refined this into the ZHL-16 model with 16 compartments and a tolerated overpressure for each, the M-value. Combined with gradient factors, which keep a margin below the M-values, it is the model most dive computers and planners use today, divecalc's dive planner included. Its page explains the model in detail.
Bubble models such as VPM and RGBM try to keep bubbles small from the start and put more stop time deep. In the 2000s deep stops became popular for that reason. A US Navy study published in 2011 then found more decompression sickness with a deep-stop schedule than with a conventional one of the same total time, and since then most divers have moved back towards fewer deep stops and more time shallow.
What gradient factors change
The same dive, 45 m for 25 minutes on trimix 21/35 with EAN50 for the decompression, planned with different gradient factors:
| Gradient factors | Stops | Deco time | Runtime |
|---|---|---|---|
| 30/85 | 21, 15, 12, 9, 6 m | 24 min | 52 min |
| 30/70 | 21, 15, 12, 9, 6 m | 32 min | 60 min |
| 50/80 | 21, 12, 9, 6 m | 26 min | 54 min |
| 100/100 | 21, 6 m | 18 min | 46 min |
A lower GF high lengthens mainly the shallow stops: from 85 to 70 the stop at 6 m grows from 16 to 22 minutes. A higher GF low starts the decompression shallower: with 50 the stop at 15 m disappears. 100/100 is Bühlmann without any margin, and only shows how much the gradient factors add. Which values to dive is a question of training and personal risk; many divers choose more conservative ones for cold water, hard work or several dive days in a row.
What deco gases change
The more oxygen a gas holds, the less inert gas, and the faster the tissues release theirs. The same dive with gradient factors 30/85:
- on the bottom gas alone: 69 minutes of decompression, surfacing after 97 minutes,
- with EAN50 from 21 m: 24 minutes, surfacing after 52 minutes,
- with EAN50 and pure oxygen from 6 m: 19 minutes, surfacing after 47 minutes.
Every deco gas is another tank to carry and to plan the gas for, and a gas that is breathed too deep is dangerous: EAN50 below its MOD of 22 m or oxygen below 6 m can cause convulsions. Check the MOD on the tank and with your buddy before every switch.
Ratio Deco
Ratio Deco is not a decompression model but a strategy: it derives the deco time from the bottom time with a simple rule, so a team can adapt the plan during the dive without a computer. Set point 1 covers dives of 40 to 50 m on trimix 21/35 with EAN50: at 45 m the deco time equals the bottom time, and every 3 m deeper add 5 minutes, every 3 m shallower take 5 off.
For the dive above it gives 25 minutes of decompression and a deep stop of one minute at 30 m. Half of the deco time is spent between 21 and 9 m, half at 6 and 3 m, and with its slow ascents the diver surfaces after 64 minutes. The deco time is close to that of Bühlmann with 30/85, but spread differently. Ratio Deco only holds for the depths and gases of its set point; outside them it is guesswork.
After the dive
- Rest, drink and keep warm; avoid hard work for the next hours.
- Flying and driving over mountain passes lower the ambient pressure further. Common guidelines ask for at least 12 hours before flying after a single no-stop dive, 18 hours after several dives or dive days, and substantially longer after decompression dives.
- Know the signs of decompression sickness and where the next oxygen and the next chamber are. Report symptoms early; waiting makes the treatment harder.
-
Dive PlannerA full plan after Bühlmann ZHL-16C
-
Ratio Deco (SP1)Deco stops by the ratio rule
This guide explains the principles; it does not replace training in decompression diving. Check results against a second source before you dive with them; see the legal notice.