Gas planning

Gas planning

Running out of gas is one of the most common causes of diving accidents, and one of the easiest to prevent. A gas plan answers three questions before the dive: how much gas do I breathe, how much does this dive take, and how much has to stay in the tank so that my buddy and I can solve a problem and still reach the surface? This guide goes through them one by one.

How much you breathe: the SCR

The surface consumption rate (SCR) is the gas a diver breathes per minute, converted to the pressure at the surface. It does not depend on depth or tank, so it is the number every gas plan starts from. Some agencies and programs call it RMV or AMV; the dive planner and Ratio Deco ask for it as "My AMV".

SCR = (Pstart − Pend) × V / ((D / 10 + 1) × t)

Pstart, Pend
tank pressure at the beginning and at the end of the dive in bar
V
water volume of the tank in liters
D
average depth of the dive in meters
t
time of the dive in minutes

A diver who breathes a 12 l tank from 200 down to 100 bar in 20 minutes at an average depth of 20 m has used 1200 l at 3 bar: 1200 / (3 × 20) = 20 l/min. Use the average depth, not the maximum, or the rate comes out too low. The rate rises with workload, cold and stress, so measure it on several dives and plan with a value from dives like the one ahead. Under stress, most divers breathe twice as much as when they are relaxed.

How much the dive takes

At depth every breath takes more gas out of the tank: at 30 m, with an ambient pressure of about 4 bar, four times as much as at the surface. The gas of a part of the dive is the SCR times the ambient pressure times the minutes; for a descent or an ascent, the mean pressure of its two ends. The gas in a tank is its volume times its pressure: a 12 l tank at 200 bar holds 2400 l. Above about 200 bar a tank holds a little less than that, because gas does not compress perfectly; keep a margin there.

An example used through this guide: a dive to 30 m for 15 minutes on air, with a 12 l tank filled to 200 bar. The diver breathes 15 l/min, the buddy 18 l/min. Descent, bottom and ascent at 15 l/min take 982.3 l, about 40 % of the tank. That is the normal gas; the question is what has to stay in the tank for when things do not go to plan.

Three ways to keep a reserve

  • A fixed reserve, often 50 bar: simple, but blind to the depth, the tank and the buddy. 50 bar in a 12 l tank at 40 m is far less gas than at 10 m.
  • The rule of thirds: one third of the gas for the way out, one third for the way back, one third in reserve. It comes from cave diving, where the way back is the way in, and works for dives that return the same way. For the example it means leaving the bottom at about 133 bar.
  • Minimum gas, also called rock bottom: the gas two divers need to solve a problem at the worst moment and to ascend from there, calculated for the dive. It is the rule the dive planner and Ratio Deco use, and the rest of this guide explains it.

Minimum gas

The worst moment of a dive is the end of the bottom time at the deepest point: the most gas is used, the way to the surface is longest. If the buddy's gas fails there, both divers breathe from one tank, and both breathe hard: the plan counts twice their SCR. They take one minute to sort out the problem at the bottom, then make the planned ascent together:

Reserve = (1 min × Pbottom + Σ P × t of the ascent) × 2 × (SCR + SCRbuddy)

Minimum gas = normal gas of descent and bottom + reserve

Turn pressure = reserve / V

Pbottom
ambient pressure at the bottom in bar
Σ P × t
for every part of the ascent its mean pressure times its minutes
V
water volume of the tank in liters

In the example the reserve is (4.013 + 3.0 × 2.513) × 2 × (15 + 18) = 762.4 l: one minute at 4.013 bar, the bottom pressure with 1.013 bar at the surface, and an ascent of three minutes at a mean pressure of 2.513 bar. Added to the gas of descent and bottom, the minimum gas is 1631.7 l of 2400 l, so the tank is big enough.

The turn pressure

The reserve divided by the volume of the tank is the turn pressure: the pressure the tank must still hold when you leave the bottom. In the example it is 762.4 / 12 = 63.5, rounded up to 64 bar. Without the buddy's higher rate, counting the own 15 l/min twice, it would be 58 bar: the buddy's consumption matters. Agree on the turn pressure before the dive; with two different tanks or rates, each diver has their own, and the team turns as soon as the first one reaches it.

For the example the rule of thirds turns earlier, at about 133 bar. But minimum gas grows with depth and with the ascent, and on a deep dive it can ask for far more than a third. A dive to 45 m for 25 minutes on trimix 21/35 in a double 12 l, with all its decompression on that gas, has a turn pressure of 380 bar: no tank holds that. The rule tells you that this dive needs a deco gas. With EAN50 from 21 m in a separate tank, the turn pressure of the double 12 drops to 44 bar.

A deco tank gets its own reserve: one and a half times the gas it needs for the plan, so that a lost or failing deco tank still leaves enough with the team.

In practice

  • Measure your SCR on real dives and update it; plan with a value from dives like the one ahead.
  • Check the pressure regularly during the dive, not only when you expect to turn.
  • Leave the bottom when the first diver reaches the turn pressure, not when the last one does.
  • If the plan needs more gas than the tank holds, change the dive: shorter, shallower, a bigger tank or a deco gas.
Calculators for this guide

This guide explains the principles; it does not replace training in gas planning. Check results against a second source before you dive with them; see the legal notice.